This lesson is tying a simple strip wing fly.
The name simple strip wing pretty much explains what differentiates this style of fly from the hair wing flies. The primary difference is the wing. We will use feathers such as Turkey, Goose, Peafowl, Swan and more. The most useful feathers for these flies are the secondaries, tail and other large body feathers. If you have them, even Parrot feathers can be used. Again, use your creativity in selecting the feathers if you don’t have the exact thing specified in a recipe.
Some new techniques featured in this lesson were either discussed in prior lessons or, are in the ‘tips and tricks’ section.
Following the lesson will be a few assorted flies of this style. Some are the same pattern as the lesson, the Red & Gold Strip Wing, with different wings.
Gold & Red Strip Wing
Hook: Mustad 36890.
Tag: Fine oval silver UNI-Tinsel.
Tail: Golden Pheasant.
Body: Rear ½ Flat gold tinsel, front ½ red UNI-Floss.
Rib: Fine oval silver UNI-Tinsel.
Collar: Red hen hackle or schlapen.
Cheeks: Jungle Cock (optional).
1. Attach tinsel tag.
2. Using smooth face pliers, flatten the tinsel to provide a flat mounting surface for the tail
3. Select a Golden Pheasant crest feather that is somewhat straight, strip the fuz from the base and up to the length you want the tail to be and flatten the feather shaft (rachis) so it will sit flat on the top of the tie in position. Notice that I bent the shaft down slightly. This will hold the tail down after it’s tied in.
4. Tail and rib tied in. Tinsel is tied in at about 5:00 when looking at the hook eye. This is slightly to the bottom rear of the shank. When the rib is applied, the rib will pull down to the 6:00 position and start at the rear and bottom of the body. Generally we want the rib to begin at this position and end on top at 12:00. Counter-ribs will be just the opposite.
5. Advance the thread in flat (untwisted) close turns to the tinsel tie in area, all the while binding the prior materials on the rear of the shank. Flatten any bumps with smooth pliers. You must be careful not to apply too much pressure using the pliers since it is easy to cut the materials. Attach the flat body tinsel underneath the shank and a ways behind the eye. We want to keep as much unnecessary bulk from the wing/head area as possible. Try to tie on and off as many of the materials in this area either to the rear, bottom or front of the shank.
6. Apply tinsel in close turns to the tail and back to the tie in area.
7. Cut waste end of tinsel and attach the floss to the bottom of the shank and flatten the floss.
8. Apply floss in flat close turns to the mid-body and back. Flatten any bumps with smooth face pliers and/or your floss burnisher, cut waste end of floss.
9. Advance the rib in five even turns and tie off underneath shank.
10. Rib complete.
11. Fold or strip one side of a hackle and attach by the tip on the reverse side of shank with two or three turns of thread.
12. Take one or two turns of hackle, tie off in front of the shank at about the 11:00 position with one or two turns, cut waste and take a turn or two more over cut end.
13. Selecting and preparing feathers for simple strip wings showing the leading edge where we will take the sections of the feathers for strip wings. Make sure you have matched the feathers well. These are Turkey secondary wing feathers but, other feathers such as Turkey tail, Peafowl, and many other similar feathers can also be used.
Reshape the barbs by “humping” (no, this is nothing “off color” here) them as shown. You can either do this before cutting them free from the feather shaft or, after. Put the concave sides together with the tips of the feathers meeting. To set the wing in, hold it with your left thumb and index fingers at the tie in spot, take one soft turn up and around the wing, on the next turn, pull up to pull the soft loop tight, take one more tight turn next to the last. You can now let go with your left hand to see how the wing looks. If it is what you like, hold the wing again with the left hand and lay down a few more tight turns one next the other towards the eye. If you weren’t happy with the wing shape/position, simply try again. You ought to be able to reposition the wing several times if needed. Do not cut waste ends yet.
14. Tie the Jungle Cock in with them over the wing as shown. You may need to flatten and twist their shafts to get them to stay where you want them.
15. Finished fly prior to head cement. I like black nail polish for heads on my display flies in particular. Your head cement will fill the voids in the thread. It is better to apply two or three thin coats rather than one thick one.
16. The finished fly with head lacquer applied.
17. Same pattern with different wing.
As always, I am happy to answer any questions you might have about these patterns. You can reach me at Ronn or 503-654-0466.
Happy Trails! ~ Ronn Lucas, Sr.